MFC-8890DW

If you have a WLAN access point/router supporting SecureEasySetup™, WPS (Wi-Fi Protected Setup) or AOSS™ (AirStation One-Touch Secure System), you can easily connect your Brother machine to your wireless network as below.

To use SecureEasySetup™, WPS or AOSS™, your WLAN access point/router must support SecureEasySetup™, WPS or AOSS™. Confirm your WLAN access point/router has the SecureEasySetup™, WPS or AOSS™ symbol as shown below. For more details, refer to the instructions provided with your access point/router.

1. Place the Brother machine within range of your SecureEasySetup™, WPS or AOSS™ access point/router.
   
   

   Note

   The range may differ depending on your environment. Refer to the instructions provided with your access point/router.
2. Hold down the SecureEasySetup™, WPS or AOSS™ button on your WLAN access point/router for a few seconds.
   
   
   
   
   

   Note

   The length holding down the button may differ depending on the WLAN access point/router. For the information on how to confirm if the WLAN access point/router is ready for use, refer to the instructions provided with your access point/router.
3. On your Brother machine, press Menu.
   
   
4. Press the Up or Down arrow key to choose Network and press OK.
   
   
5. Press the Up or Down arrow key to choose WLAN and press OK.
   
   
6. Press the Up or Down arrow key to choose SES/WPS/AOSS and press OK.
   
   
7. When WLAN Enable? is displayed, choose On to accept. The wired network interface will become inactive with this setting.
   
   
8. The machine will automatically detect which mode (SecureEasySetup™, WPS or AOSS™) your access point/router uses to configure your machine.
   
   
9. A connection result message appears on the LCD.
   
   If the LCD displays Connected, the machine has successfully connected to your access point/router. If you connect the Brother machine to a wireless network for the first time, go to STEP II: Installing the driver for network. If not, wireless setup is now complete.
   
   If the LCD displays Connection Error, a session overlap has been detected. The machine has detected more than one access point/router on your network with the SecureEasySetup™ mode, the Wi-Fi Protected Setup mode or AOSS™ mode enabled. Make sure that only one access point/router has the SecureEasySetup™ mode, the Wi-Fi Protected Setup mode or the AOSS™ mode enabled and try starting from STEP 2 again.
   
   If the LCD displays No Access Point, the machine has not detected your access point/router on your network with the SecureEasySetup™ mode, the Wi-Fi Protected Setup mode or AOSS™ mode enabled. Move the machine closer to your access point/router and try starting from STEP 2 again.
   
   If the LCD displays Connection Fail, the machine has not successfully connected to your access point/router. Try starting from STEP 2 again. If the same message is indicated again, reset the machine back to the default factory settings and try again. Click here to see the details of how to reset the machine back to the factory settings.
   
   
   LCD messages when using the SES/WPS/AOSS control panel menu
   

   LCD displays	Connection status	Action
   Setting WLAN	Searching or accessing the access point, and downloading settings from the access point.	-
   Connecting SES Connecting WPS Connecting AOSS	Connecting to the access point.	-
   Connected	Connection succeeded.	If you connect the Brother machine to a wireless network for the first time, go to STEP II: Installing the driver for network.
   Connection Error	A session overlap was detected.	Check that only one router or access point has the SecureEasySetup™ mode, the Wi-Fi Protected Setup mode or AOSS™ mode enabled and try starting from STEP 2 again.
   No Access Point	The access point detection failed.	Move the machine closer to your access point/router and try starting from STEP 2 again.
   Connection Fail	Connection failed.	1. Try starting from STEP 2 again. 2. If the same message continues, reset the machine back to the factory settings and try again. Click here to see the details of how to reset the machine back to the factory settings. 3. Try manually configuring the wireless settings, click here to configure the Brother machine for a wireless network manually.

Please continue to the following steps to install the printer driver for network connection. Even if you have printed with USB connection, you need to install the printer driver for network connection.

NOTE: The screens may differ depending on operating system being used and your Brother machine.

1. Make sure that your computer is ON and you are logged on with Administrator rights.
   
   

   Note

   If there are any programs running, close them.
2. Put the installation CD-ROM into your CD-ROM drive.
   
   

   Note

   For Windows® users:
   

   If you do not have the CD-ROM, please go to Downloads section of this website and download Full Driver & Software Package. The installation instructions are available on the download page.
   
   

   For Macintosh users:
   If you do not have the CD-ROM, please go to Downloads section of this website and download the printer driver. The installation instructions are available on the download page.

   • For Windows® users
   • For Macintosh users
   
   For Windows® users:
   
   
   1. The opening screen will appear automatically. If prompted, choose your model and language.
      
      NOTE: If the Brother screen does not appear automatically, go to My Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe.
      
      
   2. The CD-ROM main menu will appear. Click Initial Installation.
      
      
      
      
      
   3. Click Install MFL-Pro Suite, and click Yes if you accept the license agreement.
      
      
      
   
   

   Note

   For Windows Vista® and Windows® 7 users, when the User Account Control screen appears, click Allow or Yes.

   4. Follow the on-screen instructions to complete setup.
   
   For Macintosh users:
   
   
   1. Double-click Start Here OSX icon to install.
      
      
      
      
      
   2. Follow the on-screen instructions to complete setup.